1200 Deg Hi Temp Heat Black Paint Smoker Exhaust Grills

Description

Auction for 1 each aerosol can.
Winning Bid receives 1 can of Aersol. Call for case pricing.
Hi-Temp Flat/Satin Silicone enamel for Hi Temperature applications such as smokers, exhaust manifolds, mufflers, stoves and engines. Good up to 1200F. Available in aerosol, Quarts, 1's, 5's and drums. Excellent UV resistance for exterior conditions.
MasterTouch
1200
°
Black Silicone Enamel
8314 Series
PRODUCT
DESCRIPTION
A fast drying, flat black, modified silicone enamel designed for high temperature applications that require a coating to withstand continuous temperatures of 1000
°
F and surges up to 1200
°
F with no loss of adhesion.
RECOMMENDED USES
Applications include O.E.M. heat exchangers, stack, incinerators, furnace exteriors, hot piping, mufflers, exhausts and other elevated temperature metal surfaces.
Excellent for cookers, smokers and gas grills because of its excellent gloss and color retention.
PRODUCT
BENEFITS
·
Excellent Resistance to U.V. Exposure
·
Meets Proposed VOC Regulations
·
Withstands Temperatures Up to 1200
°
F
·
Can be Used As a Primer & Finish
·
Will Air Dry or Can be Force Cured or Baked
·
Excellent Flexibility For Thermal Shock
·
Fast Drying/Increased Production Time
·
Excellent Gloss & Color Retention
&
C
halk Resistance
·
Excellent Adhesion
COLORS
8314 Flat Black.
SURFACE
PREPARATION
Surface must be clean and dry.
All substrates must be cleaned free of dust, dirt, oil (including form oils & parting compounds), grease, soap residue, wax and flaking paint. Scuff sand slick, hard, glossy surfaces to promote adhesion.
Sandblast or wire-brush rusty surfaces.
Solvent wipe and /or detergent clean surface with 12 Paint Prep (Water-based Solvent Degreaser) according to SSPC-SP1.
For optimum adhesion and corrosion resistance, rusted metal should be either sandblasted SSPC-10 and obtain a 1 to 1.5 mit (25-40 micron) blast profile.
No primer is required but can be applied over inorganic zinc rich primer for increased performance.
Refer to
Surface Preparation Guide
for more detailed instructions.
APPLICATION
Mixing
: Hand stir each container thoroughly before using and occasionally while applying.
If necessary, thin sparingly with VM&P Naphtha.
Application
: May be applied by air, airless, air-assisted airless, turbo or HVLP spray.
Reduce if necessary max of 10%.
Product may also be applied by dip or flowcoat, but runs are more apparent with metallic flakes.
Recommended tip size for airless or air assisted airless spray: .013” to .015” orifice.
For air spray use 50 psi air pressure and 8 psi fluid pressure with .046” I.D fluid tip and appropriate air cap.
1.5 mils (40 microns) dry film thickness is recommended.
Two coats are recommended over bare steel.
Coverage
: One gallon will cover approximately 400 square feet per coat on smooth surfaces. Coverage figure does not include spray loss, loss due to surface porosity, surface irregularities, nor material loss when mixing.
Cleanup:
Clean spills, spatters, hands, tools and other equipment promptly with VM&P Naphtha.
Dispose of used paint and waste in accordance with local, state, and federal regulations.
Follow manufacturer’s safety recommendations when using VM&P Naphtha.
Application Precautions & Limitations
: Apply when surface, air and product are above 40ºF (4ºC) and at least 5ºF (3ºC) above the dew point.
MasterTouch
1200
°
Black Silicone Enamel
8314 Series
TECHNICAL DATA
(Based on 8314)
COLOR:
Black
VEHICLE TYPE:
Modified Silicone
WEIGHT GALLON:
8.70
+
0.2 lb/gal
WEIGHT SOLIDS:
45.1
+
2.0%
VOLUME SOLIDS:
27.6
+
2.0%
GLOSS @ 60:
5 max
VISCOSITY:
20-25 “ #2 Zahn @ 77
°
F
FLASH POINT:
47
°
F
COVERAGE:
@ 1 DRY MIL:
443 Sq.ft./gal
@ 400 SQ. FT/GAL SPREAD RATE:
Deposits 1.1 Dry mil
VOC (g/l):
573
GRIND:
#6
HMIS/NFPA:
2,3,0
FEDERAL SPECIFICATIONS:
N/A
THINNING & CLEANUP:
Toluol, Xylol
DRYING TIME @ 77
o
F AND 50% RH
TO TOUCH:
10 Minutes
TO RECOAT:
30 Minutes
­­ENVIRONMENTAL & SAFETY STATEMENT
:
This product is not formulated with any lead, chrome or mercury containing ingredients. CAUTION!
Keep away from heat and open flame.
Avoid prolonged contact with skin and breathing of vapor or spray mist.
Do not take internally.
Close container after each use.
Use only with adequate ventilation.
Use respiratory devices and other personal protective equipment required by OSHA 29CFT 1910.
KEEP OUT OF REACH OF CHILDREN.
For specific safety requirements, refer to the Material Safety Data Sheet (MSDS).
LIMITATION OF LIABILITY
:
To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance, but is subject to change without prior notice. We make no guarantee of any kind, express or implied, including merchantability and fitness for particular purposes. Liability, if any, is limited to replacement of the product or refund of the purchase price. Labor, or cost of labor, and other consequential damages are hereby excluded.